Solar Mounting Structure For Tile Roof

Flat roof solar mounting solar pv mounts rack mount solar energy Professional manufacturer of Solar Mounting System in China, install on the rooftop, ground and carport. We have passed ISO 9001-2008 quality management system, AS/NZS 1170 and SGS standard, also get AAA credit rating certificate....

Product Details

 Flat roof solar mounting solar pv mounts rack mount solar energy

 

Professional manufacturer of Solar Mounting System in China, install on the rooftop, ground and carport. We have passed ISO 9001-2008 quality management system, AS/NZS 1170 and SGS standard, also get AAA credit rating certificate.

 

Detailed Installation Procedures of Solar Energy Support

 

I. Distance between front and rear columns

In construction positioning, it is necessary to ensure that the front and rear pillars of steel piles are in the same straight line, and the straight line formed by the front and rear pillars should be perpendicular to the two straight lines formed by the front and rear pillars respectively. In addition, the straight line should not bend, and the bending range should be less than 2 mm. The height of steel piles also has corresponding requirements, and the top height of steel piles should be at the same level. The distance between the front and back pillars of steel piles is about 3 meters, and the distance between the front and back pillars is about 2 meters.

Installation effect diagram of solar energy bracket


2. Determination of Longitudinal Beam Position

The center of the welded plate on the upper edge of the front prop must be at the same horizontal height. The front prop can be fixed after reserving the corresponding length in the steel pile. The approximate angle of installation is determined according to the inclination required by the drawings, while ensuring that the center of the welding plate on the upper edge of the rear pillar is consistent in height, and the length of the steel pile can be reserved to fix the rear pillar. After the front and rear pillars are fixed, it is very important to install the longitudinal beam on the connecting plate. The central line of the longitudinal beam must coincide with the central line of the front and rear pillars. Next is the installation of cable-stayed braces: one end of the cable-stayed braces is connected with the longitudinal beam, while the other end is connected with the pillar with hoops, and the longitudinal beam must be in a parallel position.


III. Assembly

It is not difficult to install the solar energy bracket. When installing the solar energy bracket, the components should be assembled according to the instructions or design drawings. Tighten the screw properly with a wrench. Keep in mind that the step of pull-up after installation should be at the end.


IV. Choice of Direction

Solar water heaters are usually installed on roofs, sitting north and facing south, preferably in the direction of about 5-10 degrees west-south, because this direction is conducive to sun unshielded, and can also increase sunshine time.


 

Specification

 

lnstall SiteLow profile roof of open field
Tilt Angle10deg-60deg
Building HeightUp to 20m
Max Wind SpeedUp to 60m/s
Snow LoadUp to1.4KN/m2
standardsAS/NZS 1170 & DIN 1055 & Other
MaterialAluminum alloy & Stainless steel
ColorNatural
Anti-corrosiveAnodized
WarrantyTen years warranty
DuratiomMore than 20 years

 

Company Introduction

 

 

Xiamen Wanhos Solar Technology Co., Ltd. is a hightech enterprise in solar PV field specializing in solar PV products with advanced technology and excellent service. Wanhos Solar members devote themselves to research, design, manufacture and sell the steady, trustable and costefficient solar PV mounting system solutions. As one of the largest PV solar products exporter in China, the pioneering products have been installed in more than100 countries and regions since it established.

 

Management Concept

 

Wanhos Solar brought forward the standardized and internationalized management concept at the beginning of its establishment, positively brought in and strictly applied ISO9001:2008,CP, APQP,FMEA,MSA, SPC etc international quality manage system in all phases including R&D, manufacturing, marketing and after service.

 

 

 

 

Necessary info. for us to design and quote

• What is your pv panels dimension?___mm Length x___mm Width x__mm Thickness
• How many panel are you going to mount? _______Nos.
• What's the tilt angle?____degree
• What is your planned pv assmebly block? ________Nos. in a row
• How is weather there,such as wind speed and snow load?
___m/s anit-wind speed and____KN/m2 snow load.

 

 

 我的名片

Customized Solar Mounting Structure For Tile Roof free sample and its quotation and pricelist consultation, China Roof Mounting System manufacturers and suppliers,Welcome to buy our products.
Hot Tags: solar mounting structure for tile roof, suppliers China, manufacturers, factory, customized, buy, price, pricelist, quotation, free sample

Inquiry

You Might Also Like